江蘇春晨電纜有限公司生產JEM電機引接線JEM電機引出線JEM電纜，

無功補償如何提高功率因素

How to improve power factors by reactive power compensation

無功補償如何提高功率因素首先了解什么是功率因數?功率因數：是用來衡量用電設備（系列用電設備，電網的變壓器、傳輸線路，等等）的用電效率的數據。功率因數的定義公式：功率因數＝有功功率/視在功率。有功功率：是設備消耗了的，轉換為其他 ...JEM電機引接線JEM電機引出線JEM電纜

How to improve the power factor of reactive power compensation is to know what power factor and power factor first. It's a data to measure the electricity efficiency of electrical equipment (series of electrical equipment, power transformers, transmission lines, etc.). The definition formula of the power factor: the power factor = the active power / the view in the power. Active power: the equipment is consumed, converted to other...

2017-10-28 07:15

2017-10-28 07:15

刀開關的圖形符號和文字符號

The graphic symbols and characters of the knife switch

刀開關的圖形符號和文字符號刀開關的圖形符號和文字符號如圖所示。圖 刀開關的圖形符號和文字符號

The graphic symbols of the knife switch and the graphic symbols and character symbols of the word symbol knife switch are shown as shown in the diagram. Graphic symbols and literal symbols of a knife switch

2017-10-28 07:08

2017-10-28 07:08

如何計算變壓器鐵芯截面積

How to calculate the intercepting area of transformer core

如何計算變壓器鐵芯截面積小型單相變壓器多采用殼式鐵芯，變壓器鐵芯截面積與變壓器的容量有關，一般按下列經驗公式計算。 A=k√s(cm2)式中，s為變壓器的容量；k為系數。硅鋼片的k值見表。表 鐵芯凈截面系數的經驗數據根據計算得到的A值，可 ...JEM電機引接線JEM電機引出線JEM電纜

How to calculate the cross-sectional area of transformer core is mainly used in small single-phase transformers. The core area of transformer is related to the capacity of transformer. It is usually calculated according to the following empirical formula. A=k root s (cm2) type, s for transformer capacity; K coefficient. The K value of silicon steel sheet is shown in the table. The empirical data of the net section coefficient of the iron core can be calculated according to the calculated A value.

2017-10-28 07:05

2017-10-28 07:05

變壓器的基本結構和工作原理

Basic structure and working principle of transformer

變壓器的基本結構是由鐵芯和繞組（線圈）組成的。變壓器鐵芯是由兩面涂有絕緣漆的硅鋼片疊裝而成的。繞組是繞在鐵芯上的兩個匝數不等的線圈，與電源相連的繞組稱為一次繞組，與負載相連的繞組稱為二次繞組。變壓器就 ...

The basic structure of a transformer consists of a core and a winding (coil). The iron core of the transformer is made up of two silicon steel sheets coated with insulating varnish. A winding is a coil of two turns around an iron core. The winding connected to the power is called a primary winding, and the winding connected to the load is called the two winding. The transformer is...